USG all-purpose mud, sold as Sheetrock Brand All Purpose Joint Compound, is the bucket for taping and finishing drywall walls and ceilings, whether you’re a remodeler, a drywall contractor or a serious do-it-yourselfer. One bucket beds tape, fills, skims and finishes. It bonds well and dries hard, which is what you want behind tape.
USG Corporation, also known as United States Gypsum Corporation, is based in Chicago. It dates to 1902, when 30 gypsum companies merged to form the United States Gypsum Company. Since 2019 it has run as an independent subsidiary of Knauf, a privately held building-materials company. It’s the largest maker of gypsum products in North America and best known for Sheetrock panels, Sheetrock All Purpose Joint Compound and Securock glass-mat sheathing.
Bed the tape in all-purpose
Bed every tape joint in all-purpose. It carries the binder that holds paper tape to the board, and lightweight topping muds carry less of it; tape bedded in topping can pull loose the next day. Blisters come from dry spots behind the tape, so load the tape full, press it in and wipe it out firmly until there’s mud under every inch. Paper tape takes less mud than mesh on flat joints.
Finish coats and paint
The same hard finish that holds tape makes the last coats harder to sand than a lightweight topping. Feather each coat thin and the sanding stays light, or switch to a lightweight topping for the final coat only. Loosen stiff mud with a small splash of water, mixed well; a lot of water makes it shrink more as it dries and costs you an extra coat. Premixed compound is water-soluble, and heavy latex paint straight over it can soak in and peel, so seal every finished wall with a drywall primer before the paint goes on.
Where the compound stops
USG recommends this compound for interior surfaces that stay dry. In a bathroom outside the shower, hang Sheetrock Mold Tough panels and finish them with the all-purpose; USG pairs the two as a mold-resistant system, and brought out Mold Tough to improve indoor air quality. Inside the shower, the backer changes to Durock cement board, which USG calls strong, moisture-resistant and suited to kitchens and bathrooms.
That’s where the real worry comes up: is Durock waterproof, or will mold still grow behind the tile? USG describes it as water-durable and mold-resistant cement board, meaning it stays solid when it gets wet instead of softening the way gypsum does. Water and vapor still move through cement and through grout, and mold behind shower tile starts when water reaches the studs. Put a waterproofing membrane over the Durock before any tile goes on.
Other USG lines
Sheetrock UltraLight Tough is a lightweight 1/2-inch panel that USG says is up to 30% lighter than traditional drywall, with edges built to hold up through delivery and hanging, which makes it the board for ceilings. Fiberock Aqua-Tough is USG’s gypsum and cellulose underlayment for tile floors; stagger its joints off the subfloor seams. For suspended ceilings, USG also makes 4-foot white SDX cross tees and 2x4, 5/8-inch fire-rated ceiling tile.
Sheetrock All Purpose Joint Compound specs
| Spec | Sheetrock Brand All Purpose Joint Compound |
|---|---|
| Coat type | All |
| Uses | Taping, topping, skim coating, embedding tape, filling, finishing, laminating |
| Repairs | Cracks in interior plaster and masonry not exposed to moisture |
| Package | Single package |
| Working qualities | Good open time and cold bond; applies smooth and slick |
| Emissions | GREENGUARD Gold certified; low-VOC emitting material |
| System | Mold-resistant system with Sheetrock Brand Mold Tough Panels |
| Documents | Data/submittal sheet, installation guide, HPD, EPD, GREENGUARD Gold document |
| Commodity code | 380270 |
Frequently Asked Questions
Is Durock cement board waterproof?
No. It holds up when it gets wet, but water still passes through it, and most shower leaks start at the seams. Embed alkali-resistant mesh tape in thinset over every joint and inside corner (not paper tape and all-purpose mud), then run your waterproofing membrane over the whole surface, taped seams included.
How do you cut Durock cement board?
For straight cuts, score it deep along a straightedge with a carbide-tipped scoring knife, snap it over the score, then cut through the mesh on the back. A jigsaw or rotary tool with a carbide or diamond bit handles holes and curves, and a circular saw with a fiber-cement blade makes long rips. Power cutting throws silica dust, so cut outdoors and wear a respirator.
What does Sheetrock Mold Tough actually do in a bathroom?
It keeps mold from growing on the board itself, but it doesn’t stop water. The room still needs an exhaust fan vented outdoors to clear shower steam. Also leave a small gap between the bottom edge of the board and the tub or floor so it can’t wick up standing water.
Will USG fire-rated ceiling tile fit my existing grid?
The #220 tile is a 2x4 panel, 5/8 inch thick, sized for a standard 15/16-inch grid like USG’s SDX cross tees. The fire rating only counts when the whole ceiling is built as a listed assembly, rated grid included, so if the job needs a rated ceiling, build it to that listing instead of dropping rated tiles into an old grid. Cut tiles face up with a sharp utility knife against a straightedge.
Ready to Get Started?
Our building materials specialists can help you find the right USG products for your project.