Brand
Brand Overview Building Materials

Tru-Flate

Tru-Flate Couplers, Air Chucks, Tire Gauges and HI FLO Fittings Tru-Flate

Tru-Flate tire gauges, air couplers and air chucks are what a farm, shop or fleet hand uses to check a tire, fill it and hook air tools to the line. One brand covers both ends of that job, from tire patches and strings to the couplers, chucks and inflator gauges on the hose.

Tru-Flate is a tire-repair, inflation and air-accessory brand sold under the Tru-Flate® registered trademark. Highline Warren, a Memphis, Tennessee manufacturer and distributor of automotive aftermarket products, markets it. The brand’s sealing and inflating products serve the industrial, automotive and agricultural markets and the many trades that need professional-grade tire repair.

Couplers and plugs

Tru-Flate is also the trade name for a coupler profile, the automotive or T-style, so someone asking for a Tru-Flate coupler may mean the shape rather than the brand. The brand makes other profiles too, including industrial/Milton couplers, push-style couplers and A-style plugs.

Quick-connect couplers come in at least ten styles that look alike and often won’t seal on each other. The most common mistake is a new coupler on the hose with the old-style plugs still on the tools: it clicks halfway, hisses, and the compressor runs all day feeding the leak. Pick one profile and put it on every tool and every hose end. If your workplace or the neighbor you borrow tools from runs one style, match theirs. Match the thread as well, both the NPT size and whether the fitting is male or female. While you’re stuck with a mix, a universal female coupler at the hose end will usually take both industrial and automotive plugs.

HI FLO couplers and plugs

HI FLO couplers and plugs move almost three times the air of traditional couplers and plugs, which is what an impact wrench, die grinder or sander pulling hard on the line needs. When an impact wrench fades halfway through a lug nut, a standard fitting is often the choke point.

Aluminum sounds light for a fitting that gets dropped in gravel and dragged across a shop floor. HI FLO fittings are made from T6 aluminum, a heat-treated temper, and they’re corrosion resistant, so they stand up to the water that collects in every compressor line.

The HI FLO blow gun kit puts the same fittings on a blow gun, for blowing chaff out of a radiator or cleaning down a machine. Plan HI FLO as a retrofit: change the couplers and plugs over together on the hose and the tools that need the air, starting with the drop that feeds your impact wrench and grinder.

Tire tech mounting a tire in the shop

Air chucks and tire gauges

Tru-Flate’s chucks and inflator gauges handle the tire side of the air line. A ball-foot air chuck locks onto a single valve at an angle and holds with one hand. A dual-foot chuck has a straight foot and a reverse foot, so it reaches the inside valve on dual wheels; that’s the one for a truck or trailer running duals. The standard tire gauge covers cars and pickups, the truck tire gauge is the one for truck tires, and the tire inflator with gauge lets you fill and read pressure in one hand. Check pressure cold, before the tire has been driven on, because a warm tire reads high and a low one can look right.

Air line filters

Every compressor makes water, and that water rusts the inside of air tools and chucks. Tru-Flate’s filters and regulators clean and control the air before it reaches the hose. Mount the air line filter where the line leaves the tank, ahead of the regulator and the first coupler, and drain the bowl every time you drain the tank.

Tire repair kits and the wall-mount inflator

Tru-Flate also makes tire repair kits, strings and patches, sealants and glues, valves and valve caps, and hose fittings. Its 120V tankless wall-mount inflator fills a standard car tire in 3 minutes, but it mounts permanently to the wall on a 25-foot detachable recoil hose, so it suits a fixed shop bay or garage with power rather than the truck.

Inflating a tire with an air chuck and gauge

Tru-Flate HI FLO specs

SpecHI FLO couplers and plugs
Airflow rating70 CFM
Built forAir tools that need more air to work properly

Frequently Asked Questions

How do I get an accurate reading with a Tru-Flate tire gauge?

Set pressure to the number on the placard inside the driver’s door or in the owner’s manual, not the maximum molded on the sidewall, since that’s the most the tire can hold, not what the vehicle should run on. Tire pressure drops as the air gets colder, so the first hard cold snap of fall is a good time to check every tire, including the spare. Push the gauge straight onto the valve in one firm motion; if you hear a hiss, the reading’s low, so reseat it and check again.

What’s a Tru-Flate air coupler, and how do I install one without leaks?

The name can mean the brand’s couplers or the automotive T-style profile, so hold one of your tool plugs up to the new coupler before you buy, because the profiles look almost the same. On the threads, wrap PTFE tape clockwise as you look at the end of the fitting, two or three turns, and leave the first thread bare so no bits of tape get blown into the tool. Snug it with a wrench, but stop short of cranking on it, since overtightening a tapered pipe thread can crack a coupler body.

How do you use a Tru-Flate tire repair kit?

Find the puncture, pull the nail, ream the hole clean, then push a glued string through with the insertion tool, pull the tool straight back out and trim the string flush with the tread. String plugs are for small punctures in the tread only; a hole in the sidewall or shoulder needs a new tire, not a plug. Think of a string as the fix that gets you home, and when you can, have the tire taken off the rim and patched from the inside for the lasting repair.

What features does the Tru-Flate tire inflator have?

The 120V tankless wall-mount inflator uses Smart Flate preset digital technology, so you dial in the pressure you want before you start filling instead of watching a needle. It comes with a clip-on chuck that locks onto the valve and leaves your hands free. It also has an auto-reset thermal overload, so if it gets hot during a long string of tires, it shuts off and restarts once it cools down, and you don’t have to find a reset button.

Which Tru-Flate air chuck do I need?

Closed chucks hold air until you press them onto the valve, so they’re the usual choice at the end of a hose off the compressor. Open-flow chucks bleed air until they’re seated and are meant for inflator gauges and setups that expect that flow. If you’re filling big tractor or truck tires that take a while, a clip-on chuck locks onto the valve so you don’t have to stand there holding it.

Ready to Get Started?

Our building materials specialists can help you find the right Tru-Flate products for your project.