Superstrut channel is the metal strut you bolt to a wall or hang overhead to carry conduit, pipe and mechanical equipment. It’s one system: the same brand makes the channel and the fittings, clamps and accessories that bolt into it. Electricians, plumbers, mechanical contractors and serious DIYers use it.
Superstrut is the metal framing brand of ABB Installation Products, part of ABB Electrification U.S. Its complete line of fittings, clamps and accessories is made in Athens, Tennessee. ABB Installation Products lists Superstrut together with its sister line, Kindorf Metal Framing. Superstrut is also part of ABB’s EcoSolutions portfolio and has externally verified Environmental Product Declarations.
Picking the channel
Every Superstrut channel is the same width, so the fittings bolt into any of them. What changes is gauge, height and slot pattern. For overhead loads like a trapeze full of water-filled pipe, use Series 1200, the 12 gauge, because it’s the thicker steel and sags less between rods. Conduit on a wall is 14 gauge work. The mistake that comes up most is buying the lighter channel for an overhead trapeze to save a little on the order.
Height sets how stiff the channel is. The shallowest profile sits tight to a wall for light runs. The square profile, as tall as it is wide, is the everyday size. The two deeper profiles go on longer spans and heavier loads between supports.
Slotted channel lets you bolt a fitting anywhere along its length without drilling, so it’s the pick for a shop wall where runs get added later. Solid is the stiffest of the four patterns, and it’s the one to use when you’d rather drill your own holes or want a clean face showing. Punched and half-slot fall between the two.
Brackets, corners and U-bolts
A flat bracket splices two pieces of channel end to end or ties channel to a flat surface. A corner fitting joins two pieces at a right angle for a frame or shelf. A U-bolt wraps a pipe and bolts through the channel. Buy the channel nuts at the same time. A spring nut holds itself inside the channel while you start the bolt, which matters on a ladder with one hand free.
Pipe clamps
A strut pipe clamp comes in two halves that hook under the channel lip and bolt together around the pipe. Size it to the outside diameter of what you’re holding, and measure it, because conduit, steel pipe and copper tube with the same nominal size have different outside diameters. A clamp one size too big lets the pipe rattle and walk, and one size too small won’t close.
Cut ends, rust and which finish goes where
On a strut job the fresh cuts and punch holes are where rust starts. GoldGalv and SilverGalv protect every part of the strut, punch holes and cut ends included, so those two finishes cover the cuts you make on site. For electrical work, SilverGalv is the better pick. Its clear conversion coat stops white rust from forming, it leaves no residue on your hands, and its minimal electrical resistance makes grounding easy when you need it. If you’re cutting pre-galvanized or hot-dipped channel, touch the cut ends with cold galvanizing spray before it goes up.
Match the material to the location. Galvanized steel is for dry, everyday spots. Superstrut makes type 304 and type 316 stainless for harsher environments like car wash bays, pool equipment rooms and anywhere that gets hosed down with chemicals. Anywhere with chlorine or salt in the air, order type 316.
Overhead trapezes and seismic bracing
Superstrut’s listed uses include wall framing, overhead trapezes, overhead mechanical and electrical supports, and seismic bracing. A trapeze is two threaded rods dropped from the structure with a piece of channel nutted across the bottom and the runs clamped or strapped to it. Superstrut also makes the threaded rod. In the Mission Valley, where the Mission Fault is active, pipe and conduit hung on a trapeze will swing in a quake, and strut braces tie the trapeze back to the structure sideways. Get the engineer’s brace layout before the first rod goes up.
Bulk hardware and the rest of the line
For large jobs, Super-Pack cartons bulk-pack strut nuts with or without springs, square washers, pipe straps and beam clamps, all in SilverGalv and made to work with Superstrut framing. The cartons stay under 35 lbs., meet OSHA guidelines and come in smaller pack quantities for easier handling. SuperMag magnetic fittings are also made for Superstrut framing.
Superstrut channel specs
| Spec | Superstrut channel |
|---|---|
| Series 1200 | 12 gauge |
| Series 1400 | 14 gauge |
| Width | 1-5/8 in. |
| Heights | 13/16, 1-5/8, 2-7/16 and 3-1/4 in. |
| Configurations | Solid, half-slot, punched, slotted |
| Finishes | GoldGalv, SilverGalv, pre-galvanized, hot-dipped galvanized, white or green powder coat, PVC coating |
| Materials | Steel, aluminum, type 304 and type 316 stainless steel |
Frequently Asked Questions
What’s Superstrut channel made of, and when would you pick aluminum or a coated finish?
Aluminum channel weighs about a third as much as steel, so it’s easy to lift into place overhead. It also bends more under load, so keep the spans between supports shorter. PVC coating goes where the channel stays wet or sits in corrosive fumes, and powder coat goes on channel that stays in plain view and needs to look finished.
Do Superstrut brackets have to match the channel’s finish?
In a wet spot, yes, so match the fittings to the channel. A zinc-plated bracket on stainless channel rusts first and stains the stainless. Stainless hardware bolted to galvanized steel eats away the zinc around the joint once water gets in. In a dry mechanical room, galvanized fittings on galvanized channel work fine.
Can you put a Superstrut pipe clamp right on copper pipe?
Bare copper held tight against a steel clamp corrodes once moisture gets in, so put an isolator or a wrap of dielectric tape between the pipe and the clamp. On insulated pipe, size the clamp to the outside of the insulation and set a shield under it. That keeps the clamp from crushing the insulation and leaving a cold spot where condensation starts.
Is Superstrut the same as Kindorf?
No. They’re two separate metal framing brands from ABB Installation Products, and ABB lists them together as one product line. When you add to strut that’s already up, check which brand is on the channel and use that brand’s fittings so the fit and finish match the existing run.
Ready to Get Started?
Our building materials specialists can help you find the right Superstrut products for your project.