SuperForm ICF blocks are foam forms you stack, brace and fill with concrete for insulated foundation, basement and full above-grade walls. Contractors, concrete and framing crews and owner-builders use them on houses, shops, farm buildings and commercial jobs. A tie every 6 inches keeps the wall from bulging under the pour, and you need fewer add-ons.
SuperForm is a family business, founded in 1998. It was started by two journeyman carpenters from the family that still runs it. The company has more than 20 years in ICF manufacturing and runs a 63,820 sq ft plant in Pincher Creek, Alberta. SuperForm says its thick red ties, its corner tie and the overall strength of its block set it apart.
What the 12-inch block changes
The block is 12 inches tall, where competing blocks run 16 to 18 inches. Each course matches the 1-foot increments engineers and designers plan in, so estimating is wall length times height. Each tie carries less wall, and the ties run the full height of the block, so the block doesn’t settle during the pour. SuperForm says this gives up to 33% more ties per block and a flatter wall with no bulging along the block lines. The 12-inch block also allows a 12-inch rebar grid, which gives the engineer more options. It’s light enough for one person to carry in a trench or up on scaffolding.
Fewer loose parts on the stack
SuperForm says its system doesn’t need the zip ties, wire ties, glue or spray foam, FormLock, kickers or corner plywood that other systems call for. Built-in anti-lift uses the concrete’s own pressure to hold every course down, so you don’t tie or lock down each row. Rebar drops into slots in the ties with no tying. The square interlocking knobs self-align the courses and cut down on tape and glue, and SuperForm says they give 35% more friction fit than other systems. Corner blowouts are one of the biggest headaches in ICF, and SuperForm’s updated corner tie and bracket are built for that spot. SuperForm says the simpler stack lowers labor costs and gets the job finished sooner.
What it costs against a 2x6 wall
A SuperForm wall costs slightly more up front than stick framing, and SuperForm says so. Weigh that against energy: by SuperForm’s figures, buildings made entirely with its ICF have up to 60% lower energy costs than traditional construction. Compare the cost of a finished, weather-tight shell, not block against studs. The tighter envelope also lets a smaller HVAC unit hold the temperature, so have a mechanical engineer size the equipment with Manual J calculations. Put a heat recovery ventilator in every ICF building to manage fresh air.
Pouring it without a blowout
SuperForm recommends placing concrete in 4-foot lifts per hour. Experienced crews stack and pour up to 12 vertical feet, and some pours reach 15. A crew on its first ICF wall should plan on 8 to 10 feet per pour. SuperForm says that when an ICF job fails, the cause is usually the installation. A blowout, where concrete spills out of the forms, usually comes from poor bracing or from pouring too high at once. Before the truck arrives, check every wall for plumb and straightness and brace it to SuperForm’s guidelines. Vibrate the concrete as it goes in to drive out trapped air and prevent honeycombing. Builders doing a single ICF job can rent an alignment system instead of buying a full set. SuperForm offers training seminars and installation certification, and many crews have a SuperForm technical advisor on site for their first project.
SuperForm says crews can keep working through winter conditions, and the concrete core cures in a wider range of weather than conventional framing. A cold pour may still need warm concrete or insulation blankets to keep it from freezing. Waterproof anything exposed to ground moisture: basements, retaining walls and foundation walls below grade.
Fire rating in the wildland-urban interface
Every town in the Bitterroot sits in the wildland-urban interface, and so does 37% of Flathead County. On those lots the concrete core matters. SuperForm walls reach up to a 4-hour fire rating, compared with 15 to 20 minutes for a wood-framed wall, and SuperForm says independent ASTM E119 testing found its ICF withstood intense flames without structural failure. The rating depends on the wall assembly and finishes, so choose the siding and drywall to match the rating you want.
Finishing the wall
Furring strips run the full length of each block, so drywall, cabinets, trim and exterior finishes screw straight to the wall. Outside, the wall takes stucco, siding, stone veneer or brick. Inside, it takes drywall, plaster, paneling or virtually any other finish. Walls can be curved or angled. The limited warranty covers material defects in the blocks, and any coverage on installation and finishes comes through the builder.
EPS+ and Max+ foam board
EPS+ is SuperForm’s high-grade expanded polystyrene rigid insulation, and it meets CAN/ULC S701 and ASTM C578. Max+ is its graphite polystyrene board. SuperForm calls both cost-effective and durable. Add either one when the job needs sheet insulation, and it can ride on the same delivery as the block, rebar and in-floor panels. SuperForm also makes an interlocking radiant floor heat panel.
SuperForm ICF specs
| Spec | SuperForm ICF |
|---|---|
| Standard block | 4 ft long by 1 ft high |
| Tie spacing | Every 6 in |
| Tie flange | 7.25 mm (5/16 in) thick, virgin polypropylene |
| Foam between ties | 4 in, with 2 in at block ends |
| Cut lines | Every 1 in |
| Furring strips | 1.5 in, every 6 in, full block length, 1/4 in below the foam surface |
| Tensile tests | Over 850 lbs |
| Minimum curve radius | 8 ft |
| Fire rating | Up to 4 hours, depending on assembly and finishes |
| Sound rating | STC 55, against about 38 for a wood-framed wall |
| R-value | Roughly double a 2x6 wood-frame wall at about R-14 (SuperForm figure) |
| Evaluations | QAI Laboratories engineering evaluations, ICC-ES validated documentation |
Frequently Asked Questions
What is SuperForm ICF, and what’s different about how the block is built?
It’s a foam form with a flow-through design, so the concrete moves freely and bonds to every foam surface, and the grooved inside panel gives the concrete more to grip. The thick red tie flange takes a screw anywhere you need to hang something, and by the maker’s own fastener withdrawal tests it holds up to double what competitors’ ties do. Once the wall cures, the solid concrete core is impermeable to termites, rodents and insects, and the build needs no special permit beyond a standard building permit.
How much does SuperForm ICF cost compared with building with wood?
The maker sells on installation support and whole-project performance rather than the lowest block price, so a fair comparison includes labor and schedule as well as material. ICF doesn’t get the moisture and warping problems of exposed wood framing during construction, and the concrete core cures in a wider range of weather, which means fewer days lost to delays.
What products does SuperForm Products Ltd. make besides the block?
Beyond the ICF, the EPS+ and Max+ board and the radiant floor panel, there’s a range of ICF accessories and a Complete Insulation Package laid out in the company’s catalogue and brochures. For planning, it publishes an online take-off calculator, CAD drawings, technical manuals and installation guides, so the drawings and the material count can be done before the first block reaches the site.
Ready to Get Started?
Our building materials specialists can help you find the right Superform products for your project.