Spec Ops hammers, bars and hand tools are built for framing, nailing, demolition and fastening, and they’re made for contractors, framers and serious do-it-yourselfers. Start with the 22 oz framing hammer. It has a steel handle and takes a soft rubber mallet cap, so one hammer drives framing nails and taps finished flooring without marking it.
Spec Ops Tools started in early 2018. A team of veterans and industry professionals founded it, and Gary Blanchette, a veteran, is its president. The company makes heavy-duty hand tools for professionals, modeled on the rugged gear used by the U.S. military. It gives 3% of sales to veteran and first responder causes through partners including the Green Beret Foundation, the Navy SEAL Foundation and The Gary Sinise Foundation.
The 22 oz framing hammer and soft mallet cap
The 22 oz steel-handled framer is the all-day hammer in this line. Twenty-two ounces has enough head to sink 16d commons in wall framing, and it’s still light enough to control on a toenail overhead. It’s sold on its own with the cap included, and it also comes in a set with the 20 oz steel nailing hammer, the lighter choice for sheathing, blocking and punch-list work.
The soft mallet cap is non-marring Santoprene rubber that resists bouncing. Slip it over the face to knock tongue-and-groove flooring tight, seat a cabinet face frame or tap trim into place without denting it. Pull it off to go back to nails, and hang it on a nail by its two small holes so it doesn’t go missing. The cap fits only the Spec Ops 22 oz framing hammer and 20 oz nailing hammer, so if you buy it separately, match it to one of those two.
Where Spec Ops tools are made
Spec Ops tools are made in the USA and abroad, including Taiwan, China and Vietnam, and the company is adding U.S. manufacturing to employ more veterans. Whether a hammer holds up on a jobsite comes down to the standard it’s built to. Spec Ops tests its tools to meet or exceed ASME and MIL-SPEC standards in the lab, then leaves them with professional contractors for extended periods to see how they last. Spec Ops says its 28 oz framing hammer is forged from heat-treated high-carbon steel and was drop tested from 100 feet.
The rest of the Spec Ops line
The rest of the Spec Ops line covers a framing and demo day. For pulling nails and lifting trim there are 10-inch and 11-inch claw bars, an 11-inch molding bar that slips behind casing and base without chewing the wall, a 15-inch flat pry bar and a 30-inch wrecking bar for tearing out old framing and subfloor. Use the shortest bar that does the job, because a long bar gives you enough leverage to crack the drywall you meant to save; slide a scrap of wood under the heel to spread the load. The kit also includes 16- and 25-foot tapes, wood chisels from 1/4 to 1 inch, a 6-in-1 and a ratcheting screwdriver, nail sets, utility knives and levels from a 4-inch pocket level and a torpedo up to 24-, 48- and 72-inch non-magnetic Tourniquet levels. A non-magnetic level is the one for wood framing and aluminum, where a magnet only adds weight.
The 28 oz framing hammer is for headers and engineered beams, with a shock-absorbing grip, a milled face, a rip claw and a magnetic nail starter. The 2.5 lb engineering hammer is a compact demo and striking hammer with a rounded peen and a mallet cap that stands in for a dead-blow, and there’s a 4 lb version. The Delta 18-inch pry bar has a skeletonized frame and an extended 30-degree front prying surface that gets deeper behind trim and drywall. For insulation, roofing paper and flooring, the Fast Hammer Tacker is lighter than traditional tackers and has a shock-absorbing grip. Spec Ops says the torsion spring in its heavy-duty staple gun and brad nailer makes squeezing 50% easier.
Warranty
Spec Ops covers its hand tools with a limited lifetime warranty against defects in materials and workmanship for the original buyer, and blades, bits, fasteners and brads fall outside it. Keep the receipt with the tool.
Spec Ops 22 oz framing hammer specs
| Spec | Detail |
|---|---|
| Head weight | 22 oz |
| Handle | Steel |
| Model | SPEC-M22CF |
| Soft mallet cap material | Santoprene rubber (TPR) |
| Cap temperature rating | -80°F to +275°F without cracking |
| Cap fits | SPEC-M22CF framing hammer and SPEC-M20SF nailing hammer only |
| Cap color | Flat Dark Earth |
Frequently Asked Questions
Which Spec Ops hammer is best for framing?
The 22 oz steel-handled framer covers everyday wall framing, and the 28 oz is the step up for headers and engineered lumber. The 28 oz also has a side nail puller that gives you more leverage on stubborn nails in tight spots. Its lanyard hole takes SRS retention lanyards, which is worth using any time you’re working on a roof or scaffold above other people.
Are Spec Ops tools really built to military spec?
The hardest number Spec Ops publishes is for the 28 oz framing hammer. It says the hammer passed a 100-foot drop test that goes beyond the MIL-SPEC standard. For striking work, the 2.5 lb engineering hammer has composite overstrike armor protecting the handle, and Spec Ops says that doubles handle durability. The handle is where a hammer usually fails when you miss a chisel or a stake.
Ready to Get Started?
Our building materials specialists can help you find the right Spec Ops products for your project.